manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 15

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 15

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

DB9 Male

DB9 Female

Pin Male Connector

Female Connector

1

Received Line Signal Detect (Received by DTE 
Device)

Received Line Signal Detect (Transmitted 
from DCE Device)

2

Received Data (Received by DTE Device)

Transmitted Data (Transmitted from DCE 
Device)

3

Transmitted Data (Transmitted from DTE Device)

Received Data (Received by DCE Device)

4

DTE Ready (Transmitted from DTE Device)

DTE Ready (Received by DCE Device)

5

Signal Ground

Signal Ground

6

DCE Ready (Received by DTE Device)

DCE Ready (Transmitted from DCE Device)

7

Request to Send (Transmitted from DTE Device)

Clear to Send (Received by DCE Device)

8

Clear to Send (Received by DTE Device)

Request to Send (Transmitted from DCE 
Device)

9

Ring Indicator (Received by DTE Device)

Ring Indicator (Transmitted from DCE Device)

1

6

5

9

5

9

1

6

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands