manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 108

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 108

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Event Selection

SYSLOG is the warning method supported by the system. Check the corresponding box to enable 
system event warning method you wish to choose. Please note that the checkbox cannot be 
checked when SYSLOG is disabled.

System Warning – Event Selection interface

The following table describes the labels in this screen.

Label

Description

System Cold Start

Alert when system restart

Power Status

Alert when a power up or down

SNMP Authentication Failure

Alert when SNMP authentication failure.

Redundant Ring Topology Change Alert when C-Ring topology changes.
Port Event 
SYSLOG = event

› Disable 
› Link Up 
› Link Down 
› Link Up & Link Down

Save

Click to save the configurations.

Reset

Click to reset the configurations.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands