manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 69

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 69

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Port DSCP

This page allows you to configure the basic QoS Port DSCP Configuration settings for all switch ports.

Label

Description

Port

The Port column shows the list of ports for which you can configure dscp ingress and 
egress settings.

Ingress

In Ingress settings you can change ingress translation and classification settings for 
individual ports. 
There are two configuration parameters available in Ingress: 
1. Translate 
2. Classify

1. Translate

To Enable the Ingress Translation click the checkbox.

2. Classify

Classification for a port have 4 different values. 
• Disable: No Ingress DSCP Classification. 
• DSCP=0: Classify if incoming (or translated if enabled) DSCP is 0. 
•  Selected: Classify only selected DSCP for which classification is enabled as specified in 

DSCP Translation window for the specific DSCP.

• All: Classify all DSCP.

Egress

Port Egress Rewriting can be one of –  
• Disable: No Egress rewrite. 
• Enable: Rewrite enabled without remapping. 
•  Remap DP Unaware: DSCP from analyzer is remapped and frame is remarked with 

remapped DSCP value. The remapped DSCP value is always taken from the ‘DSCP 
Translation->Egress Remap DP0’ table.

•  Remap DP Aware: DSCP from analyzer is remapped and frame is remarked with 

remapped DSCP value. Depending on the DP level of the frame, the remapped DSCP 
value is either taken from the ‘DSCP Translation->Egress Remap DP0’ table or from the 
‘DSCP Translation->Egress Remap DP1’ table.

Port Policing

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands