manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 46

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 46

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

STP Statistics

This page displays the RSTP port statistics counters for bridge ports in the currently selected 
switch. 

Label

Description

Port

The switch port number of the logical RSTP port.

RSTP

The number of RSTP Configuration BPDU’s received/transmitted on the port.

STP

The number of legacy STP Configuration BPDU’s received/transmitted on the port.

TCN

The number of (legacy) Topology Change Notification BPDU’s received/transmitted on 
the port.

Discarded 
Unknown

The number of unknown Spanning Tree BPDU’s received (and discarded) on the port.

Discarded Illegal The number of illegal Spanning Tree BPDU’s received (and discarded) on the port.
Refresh

Select to refresh the page immediately.

Auto-Refresh

Check this box to enable an automatic refresh of the page at regular intervals.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands