manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 86

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 86

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Label

Description

SMAC Filter

(Only displayed when the frame type is Ethernet Type or ARP.) 
Specify the source MAC filter for this ACE.  
Any: No SMAC filter is specified. (SMAC filter status is “don’t-care”.)  
Specific: If you want to filter a specific source MAC address with this ACE, choose this 
value. A field for entering an SMAC value appears.

SMAC Value

When “Specific” is selected for the SMAC filter, you can enter a specific source MAC 
address. The legal format is “xx-xx-xx-xx-xx-xx”. A frame that hits this ACE matches this 
SMAC value.

DMAC Filter

Specify the destination MAC filter for this ACE. 
Any: No DMAC filter is specified. (DMAC filter status is “don’t-care”.)  
MC: Frame must be multicast.  
BC: Frame must be broadcast.  
UC: Frame must be unicast.
Specific: If you want to filter a specific destination MAC address with this ACE, choose 
this value. A field for entering a DMAC value appears.

DMAC Value

When “Specific” is selected for the DMAC filter, you can enter a specific destination MAC 
address. The legal format is “xx-xx-xx-xx-xx-xx”. A frame that hits this ACE matches this 
DMAC value.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands