manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 59

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 59

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Label

Description

Trap Mode

Indicates the SNMP trap mode operation. Possible modes are:  
Enabled: Enable SNMP trap mode operation.  
Disabled: Disable SNMP trap mode operation.

Trap Version

Indicates the SNMP trap supported version. Possible versions are:  
SNMP v1: Set SNMP trap supported version 1.  
SNMP v2c: Set SNMP trap supported version 2c.  
SNMP v3: Set SNMP trap supported version 3.

Trap Community Indicates the community access string when send SNMP trap packet. The allowed string 

length is 0 to 255, and the allowed content is the ASCII characters from 33 to 126.

Trap Destination 
Address

Indicates the SNMP trap destination address.  
Trap Destination IPv6 Address

Trap Destination 
IPv6 Address 

Provide the trap destination IPv6 address of this switch. IPv6 address is in 128-bit 
records represented as eight fields of up to four hexadecimal digits with a colon 
separating each field (:). For example, ‘fe80:215:c5ff:fe03:4dc7’. The symbol ‘::’ is a 
special syntax that can be used as a shorthand way of representing multiple 16-bit 
groups of contiguous zeros; but it can only appear once. It also used a following legally 
IPv4 address. For example, ‘::192.1.2.34’.

Trap 
Authentication 
Failure

Indicates the SNMP entity is permitted to generate authentication failure traps. Possible 
modes are:  
Enabled: Enable SNMP trap authentication failure.  
Disabled: Disable SNMP trap authentication failure.

Trap Link-up and 
Link-down

Indicates the SNMP trap link-up and link-down mode operation. Possible modes are:  
Enabled: Enable SNMP trap link-up and link-down mode operation.  
Disabled: Disable SNMP trap link-up and link-down mode operation.

Trap Inform ModeIndicates the SNMP trap inform mode operation. Possible modes are:  

Enabled: Enable SNMP trap inform mode operation.  
Disabled: Disable SNMP trap inform mode operation.

Trap Inform 
Timeout(seconds)

Indicates the SNMP trap inform timeout. The allowed range is 0 to 2147.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands