manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 33

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 33

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

LACP System Status

This page provides a status overview for all LACP instances.

Label

Description

Aggr ID

The Aggregation ID associated with this aggregation instance. For LLAG the id is shown 
as ‘isid:aggr-id’ and for GLAGs as ‘aggr-id’

Partner  
System ID

The system ID (MAC address) of the aggregation partner.

Partner Key

The Key that the partner has assigned to this aggregation ID.

Last Changed

The time since this aggregation changed.

Local Ports

Shows which ports are a part of this aggregation for this switch/stack. The format is: 
“Switch ID:Port”.

Refresh

Select to refresh the page immediately.

Auto-Refresh

Check this box to enable an automatic refresh of the page at regular intervals.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands