manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 133

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 133

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

STP

STP>

Configuration                 
Version [<stp_version>]   
Non-certified release, v
Txhold [<holdcount>]lt 15:15:15, Dec  6 2007
MaxAge [<max_age>]
FwdDelay [<delay>]
bpduFilter [enable|disable]
bpduGuard [enable|disable]
recovery [<timeout>]
CName [<config-name>] [<integer>]
Status [<msti>] [<port_list>]
Msti Priority [<msti>] [<priority>]
Msti Map [<msti>] [clear]
Msti Add <msti> <vid>
Port Configuration [<port_list>]
Port Mode [<port_list>] [enable|disable]
Port Edge [<port_list>] [enable|disable]
Port AutoEdge [<port_list>] [enable|disable]
Port P2P [<port_list>] [enable|disable|auto]
Port RestrictedRole [<port_list>] [enable|disable]
Port RestrictedTcn [<port_list>] [enable|disable]
Port bpduGuard [<port_list>] [enable|disable]
Port Statistics [<port_list>]
Port Mcheck [<port_list>]
Msti Port Configuration [<msti>] [<port_list>]
Msti Port Cost [<msti>] [<port_list>] [<path_cost>]
Msti Port Priority [<msti>] [<port_list>] [<priority>]

Aggr

Aggr>

Configuration
Add <port_list> [<aggr_id>]
Delete <aggr_id>
Lookup [<aggr_id>]
Mode [smac|dmac|ip|port] [enable|disable]

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands