manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 121

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 121

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Synchronization-PTP

This page allows the user to configure and inspect the current PTP clock settings.

Label

Description

One_pps_mode This Selection box will allow you to select the One_pps_mode configuration. 

The following values are possible: 
1. Output : Enable the 1 pps clock output 
2. Input : Enable the 1 pps clock input 
3. Disable : Disable the 1 pps clock in/out-put

External Enable This Selection box will allow you to configure the External Clock output. 

The following values are possible: 
1. True : Enable the external clock output 
2. False : Disable the external clock output

VCXO_Enable

This Selection box will allow you to configure the External VCXO rate adjustment. 
The following values are possible: 
1. True : Enable the external VCXO rate adjustment 
2. False : Disable the external VCXO rate adjustment

Clock Frequency This will allow to set the Clock Frequency. 

The possible range of values are 1 - 25000000 (1 - 25MHz)

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands