Comnet CNGE20MS Installation And Operation Manual Download Page 123

Page: 123 / 144

INS_CNGE24MS-OB(M,S)_REV–

09/12/12 PAGE 123

INSTALLATION AND OPERATION MANUAL

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

System Reboot

You can reset the stack switch on this page. After reset, the system will boot normally as if you had
powered-on the devices

Label

Description

Yes

Select to reboot device.

Select to return to the Port State page without rebooting.

Factory Defaults

You can reset the configuration of the stack switch on this page. Only the IP configuration is
retained.

Label

Description

Keep IP

Mark this box to retain current IP settings upon reset

Keep User/
Password

Mark this box to retain current Username and Password

Yes

Select to reset the configuration to Factory Defaults.

Select to return to the Port State page without resetting the
configuration

Summary of Contents for CNGE20MS

















































































































































Search results

Summary of Contents for CNGE20MS

Reviews:

Brands by name

Popular brands

Comnet CNGE20MS, Installation And Operation Manual

Search results

Summary of Contents for CNGE20MS

Reviews:

Brands by name

Popular brands