manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 141

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 141

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

DeviceBinding

Devicebinding>

Mode [enable|disable]                                             
Port Mode [<port_list>] [disable|scan|binding|shutdown]           
Port DDOS Mode [<port_list>] [enable|disable]                     
Port DDOS Sensibility [<port_list>] [low|normal|medium|high]      
Port  DDOS  Packet  [<port_list>]  [rx_total|rx_unicast|rx_multicast|rx_broadcast|tcp|udp]                                                            
Port DDOS Low [<port_list>] [<socket_number>]                     
Port DDOS High [<port_list>] [<socket_number>]                    
Port DDOS Filter [<port_list>] [source|destination]               
Port DDOS Action [<port_list>] [do_nothing|block_1_min|block_10_mins| 
block|shutdown|only_log|reboot_device]                                       
Port DDOS Status [<port_list>]                                    
Port Alive Mode [<port_list>] [enable|disable]                    
Port Alive Action [<port_list>] [do_nothing|link_change|shutdown|only_log|reboot_device]
Port Alive Status [<port_list>]                                   
Port Stream Mode [<port_list>] [enable|disable]                   
Port Stream Action [<port_list>] [do_nothing|only_log]            
Port Stream Status [<port_list>]                                  
Port Addr [<port_list>] [<ip_addr>] [<mac_addr>]                  
Port Alias [<port_list>] [<ip_addr>]                              
Port  DeviceType  [<port_list>]  [unknown|ip_cam|ip_phone|ap|pc|plc|nvr]                                                                             
Port Location [<port_list>] [<device_location>]                   
Port Description [<port_list>] [<device_description>]

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands