manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 8

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 8

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Rack-mount Installation

The device comes with two mounting kits for you to install the device to a rack. Before installation, 
keep the following guidelines in mind.

Elevated Operating Ambient: If installed in a closed environment, make sure the operating 

ambient temperature is compatible with the maximum ambient temperature (Tma) specified by 

the manufacturer.

Reduced Air Flow: Make sure the amount of air flow required for safe operation of the equipment 

is not compromised during installation.

Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous condition 

due to uneven mechanical loading.

Circuit Overloading: Consideration should be given to the connection of the equipment to the 

supply circuit and the effect that overloading of the circuits might have on overcurrent protection 

and supply wiring. Appropriate consideration of equipment nameplate ratings should be used 

when addressing this concern.

Wall-Mounting Measurement (Unit = mm)

Follow the steps below to install the device to a rack.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands