manualshive.com logo in svg

Comnet CNGE20MS, Installation And Operation Manual

Share
Download
Comnet CNGE20MS Installation And Operation Manual Download Page 62

INS_CNGE24MS-OB(M,S)_REV–

09/12/12     PAGE 62

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

SNMP-Groups

Configure SNMPv3 groups table on this page. The entry index keys are Security Model and 
Security Name.

Label

Description

Delete

Check to delete the entry. It will be deleted during the next save.

Security Model

Indicates the security model that this entry should belong to. Possible 
security models are:  
v1: Reserved for SNMPv1.  
v2c: Reserved for SNMPv2c.  
usm: User-based Security Model (USM).

Security Name

A string identifying the security name that this entry should belong 
to. The allowed string length is 1 to 32, and the allowed content is the 
ASCII characters from 33 to 126.

Group Name

A string identifying the group name that this entry should belong to. 
The allowed string length is 1 to 32, and the allowed content is the 
ASCII characters from 33 to 126.

Summary of Contents for CNGE20MS

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands