Comnet CNGE20MS Installation And Operation Manual Download Page 71

Page: 71 / 144

INS_CNGE24MS-OB(M,S)_REV–

09/12/12 PAGE 71

INSTALLATION AND OPERATION MANUAL

CNGE24MS-OB(M,S)

TECH SUPPORT: 1.888.678.9427

Queue Policing

This page allows you to configure the Queue Policer settings for all switch ports.

Label

Description

Port

The port number for which the configuration below applies.

Enable(E)

Controls whether the queue policer is enabled on this queue.

Port Scheduler

This page provides an overview of QoS Egress Port Schedulers for all switch ports.

Label

Description

Port

The logical port for the settings contained in the same row.
Click on the port number in order to configure the schedulers.

Mode

Shows the scheduling mode for this port.

Shows the weight for this queue and port.

Summary of Contents for CNGE20MS

















































































































































Search results

Summary of Contents for CNGE20MS

Reviews:

Brands by name

Popular brands

Comnet CNGE20MS, Installation And Operation Manual

Search results

Summary of Contents for CNGE20MS

Reviews:

Brands by name

Popular brands