Comnet CNGE20MS Installation And Operation Manual Download Page 1

INSTALLATION AND OPERATION MANUAL 

CNGE24MS-OB(M,S)

INDUSTRIAL 24-PORT ALL GIGABIT MANAGED ETHERNET SWITCH  

WITH 16 TX PORTS AND 8 SFP PORTS PLUS OPTICAL BYPASS

The ComNet CNGE24MS-OB is a Managed Ethernet Switch with sixteen 
10/100/1000 Mbps TX ports and eight 100/1000 Mbps SFP* ports that use 
ComNet SFPs for fiber type, connector type and distance. This switch also 
includes two sets of bypass ports that ensure network integrity during power  
loss or maintenance. The CNGE24MS-OB is IEEE802.3-compliant and offers 
multiple Ethernet redundancy protocols (ComRing, C-Ring, and MSTP/RSTP/
STP) which protect your applications from network interruptions or temporary 
malfunctions by redirecting transmission within the network. Unlike most 

 

Ethernet switches, these environmentally hardened units are designed for 
deployment in difficult operating environments, and are available for use 

 

with either conventional CAT-5e copper or optical transmission media.

Rev. 11.18.16

Summary of Contents for CNGE20MS

















































































































































Reviews: