manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 7

7

●

The higher the control module is in the vehicle, the better the remote range will be. If you put the
control module under a seat or inside a metal dashboard, range will diminish.

Some good control module locations: above the glove box, inside the center console, above the
under-dash fuse box, above the radio, etc.

locations for dual stage shock sensor

Some things to remember about where to mount the shock sensor:

●

Never install the sensor in the engine compartment!

●

Find a spot close to the control module so that the wires do not need to be extended. Keep it
away from the heater core (or any other heat sources) and any obvious leaks. 

How the sensor is mounted is the most important factor in its performance. We recommend two methods:

●

Using double-sided tape or hook-and-loop fastener to mount to a trim panel or an air duct, or 

●

Wire-tying to a wire harness.

If mounting the sensor where it cannot be easily reached for adjustment, hook-and-loop fastening
tape (such as Velcro) is recommended for ease of removal for future adjustments.

N

NO

OTTEE:: In many vehicles, tying the sensor to a steering column or screwing it to metal will result in poor sensi-

tivity, especially at the rear of the vehicle.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands