manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 17

17

primary harness (H1) wire connection guide

H1/1 ORANGE

(-) ground-when-armed output

This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon
as the system is disarmed. The orange wire may be wired to an optional starter kill relay.

H1/2 WHITE

(+/-) selectable light flash output

As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity
jumper under the sliding door is moved to the opposite position (see Internal Programming Jumper
section of this guide), this wire supplies a (-) 200 mA output. This is suitable for driving (-) light con-
trol wires in Toyota, Lexus, BMW, some Mitsubishi, some Mazda, and other model cars.

(+) Positive Light Flash Output

(-) Light Flash Output

N

NO

OTTEE:: For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light

flash output. (See the Internal Programming Jumper section of this guide.) A standard automotive SPDT relay must
be used on the H1/2 light flash output harness wire.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands