manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 49

49

4. 

Press and release the override switch within 5 seconds. The LED will flash in

groups indicating the last two zones that triggered the unit for one minute or until the igni-
tion is turned off.

N

NO

OTTEE:: The warning triggers are not stored to memory and will not be reported.

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free oper-
ation. The following test procedure must be used to verify proper installation and operation of the
system. The installation must be completed before testing, including connection to the brake switch
and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system.

Once the engine is running, press the brake pedal. The engine should shut down immediately. If
the engine continues to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the

remote start system. The vehicle should not start. If the starter engages, check your hood pin and
connections.

3. Test the NEUTRAL SAFETY shutdown circuit:

IIm

mp

poorrtta

anntt!! Make sure there is adequate clearance to the front and rear of the vehicle before attempting this test. 

a. Make sure the hood is closed and no other shutdown circuits are active.

b. Set the emergency brake.

c. Turn the ignition key to the run position but do not start the engine.

d. Put the vehicle in Drive (D).

e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake
to shutdown the remote start system.

f. Activate the remote start system.

●

If the starter engages, immediately step on the brake to shut down the system. If it does

engage, recheck the neutral safety input connection. The vehicle may use a mechanical neutral
safety switch. (See H3/5 BLACK/WHITE neutral safety switch input in Remote Start Harness Wire
Connection Guide section of this guide.)

●

If the starter does not engage, the test is complete.

Once the system passes the three tests, the vehicle can be re-assembled and delivered. Do not the
use the remote start system or finalize the installation if it fails any of the safety check tests.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands