manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 29

29

bypassing GM vehicle anti-theft systems (VATS)

Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the
VATS decoder module does not measure the proper resistance when the vehicle is started, the starter
and fuel pump may be disabled for up to ten minutes. An optional "VATS pack" of resistors is avail-
able. One of the resistors in the pack will match the resistor in the key.

The VATS wires will be two very light-gauge wires coming out of the steering column. The colors of
the wires vary, but they are often contained in orange tubing - either both will be white wires, or one
wire will be purple/white and the other white/black. Determine the value of the resistor in the key.
Then follow the diagram below to bypass VATS during remote start operation. Use the BLUE output
status wire from the Satellite harness (pin #1) to control the relay.

N

NO

OTTEE:: When connecting to the VATS wires, it is not important which wire is cut.

BLUE STATUS SATELLITE

HARNESS (PIN #1)

(+) 12V CONSTANT FUSED

85

86

30

87 87A

TO IGNITION KEY SWITCH

X

X

CUT

PROPER RESISTOR VALUE

TO VATS DECODER MODULE

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands