manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 34

34

tach threshold on/off

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts
in their ignition systems. The unit may have trouble learning the tach signal in these vehicles.
Changing the jumper to the ON setting changes the trigger threshold of the digital tach circuit so it
will work properly with these vehicles. These vehicles include many newer
Dodge/Chrysler/Plymouths, such as the Neon Cirrus/Stratus/Breeze and LH-based cars.

light flash (+)/(-)

This jumper is used to determine the light flash output. In the (+) position, the on-board relay is
enabled and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board
relay is disabled. The WHITE wire, H1/2, will supply a 200 mA (-) output suitable for driving fac-
tory parking light relays.

N

NO

OTTEE:: For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light

flash output. A standard automotive SPDT relay must be used on the H1/2 light flash output harness wire.

remote programming routine

The system comes with remotes that have been taught to the receiver. The receiver can store up to 4
different remote codes in memory. Use the following program routine to add remotes to the system
or to change button assignments if desired.

The program routine may be locked if previously programmed using the Pro security programmer.
If the horn generates one long honk when attempting to program the unit, the program routine is
locked and must be unlocked using the Pro security programmer before proceeding.

The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic
sequence of steps to remember whenever programming this unit: Door, Key, Choose, Transmit and
Release.

1. Open a door.

(The GREEN wire, H1/5, or the VIOLET, H1/7 must be connected.)

2. Key.

Turn the ignition to the ON position.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands