Clarion Ungo Pro Security SR1000 Installation Manual Download Page 48

Page: 48 / 55

remote start diagnostics

1. With the ignition OFF, press and

hold

the override button.

2. Turn the ignition ON and then back OFF while

holding

the override button.

3. Release the override button.

4. Press and release the override button. The LED will report the last shutdown for one minute or

until the ignition is turned on.

security diagnostics

The system stores the last two full triggers in memory. These are not erasable. Each time the unit sees
a full trigger, the older of the two triggers in memory will be replaced by the new trigger. To access
long term event history:

1. With the ignition off, press and hold the override switch.

2. Turn on the ignition.

3. Release the override switch.

LED FLASHES

SHUTDOWN MODE

One

Timed out

Two

Over-rev shutdown

Three

Low or no RPM

Four

Remote shutdown (or optional push-button)

Six

(-) Shutdown (H3/3 GRAY) or (+) Shutdown (H3/4 BROWN)

Seven

(-) Neutral safety shutdown (H3/6 BLACK/WHITE)

Eight

Wait-to-start timed out

Summary of Contents for Ungo Pro Security SR1000























































Search results

Summary of Contents for Ungo Pro Security SR1000

Reviews:

Brands by name

Popular brands

Clarion Ungo Pro Security SR1000, Installation Manual

Search results

Summary of Contents for Ungo Pro Security SR1000

Reviews:

Brands by name

Popular brands