manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 4

4

warning! safety first

The following safety warnings must be observed at all times:

●

Due to the complexity of this system, installation of this product must only be performed by an
authorized dealer.

●

When properly installed, this system can start the vehicle via a command signal from the remote.
Therefore, never operate the system in an area that does not have adequate ventilation. The
following precautions are the sole responsibility of the user; however, authorized dealers should
make the following recommendations to all users of this system:
1. Never operate the system in an enclosed or partially enclosed area without ventilation (such

as a garage).

2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced,

the remote start system must be disabled using the installed toggle switch.

3. It is the user's sole responsibility to properly handle and keep out of reach from children all

remotes to assure that the system does not unintentionally remote start the vehicle.

4.

THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING
AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS
TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES
REMAIN CLOSED.

●

Use of this product in a manner contrary to its intended mode of operation may result in property
damage, personal injury, or death. Except when performing the Safety Check outlined in this
installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never
remotely start the vehicle with the keys in the ignition. The user will be responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely
start while the car is in gear. This testing should be performed by an authorized Directed
Electronics dealer in accordance with the Safety Check outlined in this product installation guide.
If the vehicle starts in gear, cease remote start operation immediately and consult with the user
to fix the problem immediately.

●

After the remote start module has been installed, test the remote start module in accordance with
the Safety Check outlined in this installation guide. If the vehicle starts when performing the
Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The
remote start module must be removed or properly reinstalled so that the vehicle does not start in
gear. All installations must be performed by an authorized dealer. 

OPERATION OF THE REMOTE

START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY
RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE
UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. UNGO WILL
NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands