manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 18

18

H1/3 WHITE/BLUE

remote start (-) activation input

This input comes from the factory set to 2 activation pulses. This means that it is necessary to have
2 consecutive ground pulses on the white/blue wire for the remote start to activate or to deactivate.
The same holds true for the remote control activation when set to a two pulse setting it is necessary
to press the 

button twice for the remote start to activate or deactivate.

N

NO

OTTEE:: When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed it will affect

both activation inputs; the White/Blue wire and the remote control activation.

H1/4 BLACK/WHITE

(-) 200 mA domelight supervision output

Connect this wire to the optional domelight supervision relay as shown below:

IIM

MPPO

ORRTTA

AN

NTT!! This output is only intended to drive a relay. It cannot be connected directly to the domelight cir-

cuit, as the output cannot support the current draw of one or more light bulbs. 

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands