manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 22

22

H2/2 GRAY/BLACK

(-) diesel wait-to-start bulb input

Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb
in the dashboard. In most diesels the wire is negative (ground turns on the bulb) and the
GRAY/BLACK wire can be directly connected to the wire in the vehicle. If the vehicle uses a positive
wire (12V to turn on the bulb) a relay must be used to change the polarity. (See Finding the Wires
You Need section of this guide.) Here are some common colors of this wire:

●

Chevrolet and GMC trucks - Light blue or dark blue

●

Ford Trucks - Black/pink

●

Dodge Ram Trucks - Orange/black or black/orange

N

NO

OTTEE!! A 1-amp diode must be installed in line on the factory wire between the wait-to-start indicator and the

ECM. (See the following diagram for details.)

H2/3 GREEN/WHITE

factory alarm rearm

This wire sends a negative pulse every time the remote start shuts down or the doors are locked. This
can be used to pulse the arm wire of the vehicle's factory anti-theft device. Use a relay to send a (-)
or (+) pulse to the arm wire.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands