manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 52

52

2. Was the Tach Learn successful? The LED must light solid and bright to indicate a successful learn.

3. Make sure that there is a tach signal at the purple/white tach input wire of the remote start. If

there is not a tach signal, recheck the connection to the vehicle’s tach wire and make sure the
wire is not broken or shorted to ground leading to the remote start.

●

The vehicle will start, but will only run for 10 seconds.

1. Is the remote start programmed for voltage sense? Try programming the unit for low voltage ref-

erence. If this does not work, a tach wire should be used.

2. Check diagnostics.

●

The climate control system does not work while the unit is operating the vehicle.

Either the wrong accessory wire is being energized or more than one ignition or accessory wire must
be energized in order to operate the climate control system.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands