Clarion Ungo Pro Security SR1000 Installation Manual Download Page 47

Page: 47 / 55

timer mode

By pressing the remote

and

buttons the parking lights will flash 4 times and then start the

vehicle and run for the set duration. The remote start can be shut off by the remote by pressing the
remote start button

and remain in timer mode, but if any other shut down zones or the ignition

becomes active the timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. A 1-second delay will start.

4. The system will start the car and will run for the specified duration, unless shut down by the

remote start button

. If shut down with the remote start button

the system will remain in

timer mode.

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down

wires.

To exit timer mode, turn the ignition switch on any time the engine is not running. The parking lights

will flash 4 times, indicating timer mode has been exited.

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down

wires.

table of zones

When using the Diagnostic functions, use the Table of Zones to see which input has triggered the sys-
tem. It is also helpful in deciding which input to use when connecting optional sensors and switches.

OTTEE:: The warning response does not report on the LED.

ZONE NO.

TRIGGER TYPE

INPUT DESCRIPTION

Multiplexed Input

BLUE (H1/6)

Multiplexed Shock Sensor Input Mux BLUE wire.

Door Trigger

GREEN (H1/5) and VIOLET (H1/7).

Multiplexed Shock Sensor

Mux GREEN wire

Ignition

Yellow ribbon harness wire

Hood Brake Trigger

GRAY on the 5-pin shutdown harness.

Summary of Contents for Ungo Pro Security SR1000























































Search results

Summary of Contents for Ungo Pro Security SR1000

Reviews:

Brands by name

Popular brands

Clarion Ungo Pro Security SR1000, Installation Manual

Search results

Summary of Contents for Ungo Pro Security SR1000

Reviews:

Brands by name

Popular brands