manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 20

20

H1/8 BLACK

(-) chassis ground connection

Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than
your own screw. (Screws tend to either strip or loosen with time.) We recommend grounding all your
components, including the siren, to the same point in the vehicle.

H1/10 BROWN

(+) siren output

Connect this to the red wire of the siren. Connect the black wire of the siren to (-) chassis ground,
preferably at the same point you connected the control module’s black ground wire.

H1/11 RED

(+)12V constant power input

Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the
constant 12V supply to the ignition switch.

N

NO

OTTEE:: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 15A fuse in the har-

ness for this purpose. This fuse protects the module itself.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands