manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 5

5

installation points to remember

IIM

MPPO

ORRTTA

AN

NTT!! This product is designed for fuel-injected, automatic transmission vehicles only. Installing it in a stan-

dard transmission vehicle is dangerous and is contrary to its intended use.

before beginning the installation

●

Please read this entire installation guide before beginning the installation. The installation of this
remote start system requires interfacing with many of the vehicle’s systems. Many new vehicles
use low-voltage or multiplexed systems that can be damaged by low resistance testing devices,
such as test lights and logic probes (computer safe test lights). Test all circuits with a high quality
digital multi-meter before making connections.

●

Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air
bag, avoid disconnecting the battery if possible. Many airbag systems will display a diagnostic
code through their warning lights after they lose power. Disconnecting the battery requires this
code to be erased, which can require a trip to the dealer.

●

Check with the customer on status LED location.

●

Remove the domelight fuse. This prevents accidentally draining the battery.

●

Roll down a window to avoid being locked out of the car.

after the installation

●

Test all functions. The “Using Your System” section of the Owner's Guide is very helpful when
testing.

●

When testing, don’t forget that this system is equipped with false alarm prevention circuitry. This
circuitry can bypass trigger zones, making them appear to stop working. See the False Alarm
Prevention section.

●

Review and complete the Safety Check section of this guide prior to the vehicle reassembly.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands