manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 32

32

shock sensor harness, 4-pin connector

GREEN

(-) multiplex input, zone 2

Inputs shorter than 0.8 seconds will trigger the warning response, while inputs longer than 0.8 sec-
onds will trigger full alarm sequence and report Zone Two. If installing an optional dual stage sen-
sor, connect to the green wire as shown below. The diagram below eliminates the need for diodes
to isolate the sensors.

Diagram for adding optional dual stage sensor to green wire (Zone 2):

BLUE

(-) multiplex input, zone 2

Inputs shorter than 0.8 seconds will trigger the warning response, while inputs longer than 0.8 sec-
onds will trigger full alarm sequence and will also report Zone Two.

RED and BLACK: RED is (+)12V constant, BLACK is (-) ground

N

Noottee:: Do not use these for anything besides the plug-in shock sensor.

BLUE WIRE OF

PRE-WIRED PLUG

GREEN WIRE OF

PRE-WIRED PLUG

BLUE WIRE FROM PLUG-IN

SHOCK SENSOR

BLUE AND GREEN WIRES

FROM DUAL STAGE SENSOR

GREEN WIRE FROM

PLUG-IN SHOCK SENSOR

X

X

CUT

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands