manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 36

36

Learn Routine will be exited if:

●

Door is closed.

●

Ignition is turned off.

●

Program switch is pressed too many times.

●

More than 15 seconds between steps.

remote configurations

The remotes can be programmed with the standard or single button arm/disarm configurations by
using the auto learn functions in the Remote learn routine.

standard configuration

A remote that uses the standard configuration operates similarly to many factory keyless entry
remotes. A standard configuration remote allows arming, disarming, and panic mode activation
with separate buttons. When programmed for standard configuration, the remote buttons are
assigned to the following functions:

operates

Arm/Lock, Panic ON/Panic OFF

operates

Disarm/Unlock/Panic OFF

operates

Remote start

operates

Channel 2—trunk release

and operates

Timer 

Mode

and operates

Short 

Run/Turbo 

timer

and operates

Channel 

4

and operates

Channel 

5

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands