Clarion Ungo Pro Security SR1000 Installation Manual Download Page 39

Page: 39 / 55

The module programming routine will be exited if:

●

The door is closed.

●

The ignition is turned on.

●

The override switch is pressed too many times.

●

More than 15 seconds elapses between programming steps.

One long siren chirp indicates that the module programming routine has been exited.

feature menus

The default settings are indicated in bold type. Features that have additional settings that can be pro-
grammed using the Pro Security Programmer are indicated with an asterisk (*).

menu #1 - basic features

FEATURE NUMBER

ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

1-1

Active arming

Passive arming

1-2

Arm/disarm chirps ON

Arm/disarm chirps OFF

1-3

Ignition lock ON*

Ignition lock OFF*

1-4

Ignition unlock ON

Ignition unlock OFF

1-5

Active locking only

Passive locking

1-6

Panic with ignition ON

No panic with ignition ON

1-7

0.8 second door lock pulses

3.5 second door lock pulses

1-8

Forced passive arming ON

Forced passive arming OFF

1-9

Automatic engine disable ON

Automatic engine disable OFF

1-10

Armed When Driving (AWD) ON

AWD OFF

1-11

Anti-code grabbing ON

Anti-code grabbing OFF

Summary of Contents for Ungo Pro Security SR1000























































Search results

Summary of Contents for Ungo Pro Security SR1000

Reviews:

Brands by name

Popular brands

Clarion Ungo Pro Security SR1000, Installation Manual

Search results

Summary of Contents for Ungo Pro Security SR1000

Reviews:

Brands by name

Popular brands