manualshive.com logo in svg

Clarion Ungo Pro Security SR1000, Installation Manual

Share
Download
Clarion Ungo Pro Security SR1000 Installation Manual Download Page 37

37

The standard configuration also allows the user to utilize Remote Sensor Bypass (described in the fol-
lowing section).

remote sensor bypass

Remote Sensor Bypass is a feature that allows the user to select which of the system's inputs or sen-
sors will be active and which will be bypassed when the system is armed. (See Table of Zones sec-
tion of this guide.) Remote Sensor Bypass can only be accessed from a standard configuration
remote. Pressing the arm button of the standard configuration remote again within five seconds of
arming the system will activate the Remote Sensor Bypass feature. Each time the arm button is
pressed again, a different security level is selected. The different levels of security are selected as fol-
lows:

●

Pressing 

one time: The siren chirps once. The system is armed.

●

Pressing 

a second time within five seconds: The siren chirps twice followed by a long 

chirp. Zone Two is now bypassed.

●

Pressing 

a third time within five seconds: The siren chirps three times followed by a long

chirp. Zone Four is now bypassed.

●

Pressing 

a fourth time within five seconds: The siren chirps four times followed by a long

chirp. Zones Two and Four are now bypassed.

●

Pressing 

a fifth time within five seconds: The siren chirps five times followed by a long

chirp. All input zones, except the ignition, are now bypassed.

module programming

The module programming routine dictates how the unit operates. Due to the number of fea-
tures, the features have been divided into two menus. It is possible to access and change any

of the feature settings using the override switch. However, this process can be greatly simplified by
using the Pro Security Programmer. Any of the settings can be changed and then assigned to one of
up to four remotes, a feature called individual recognition. Each time that particular remote is used
to disarm the system, the assigned feature settings will be recalled. Individual recognition is only pos-
sible when programming the unit via the Pro security programmer.

Summary of Contents for Ungo Pro Security SR1000
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands