manualshive.com logo in svg

Chevrolet TrailBlazer, Service Manual

The Chevrolet TrailBlazer Owner's Manual is the ultimate guide to understanding and operating this powerful SUV. Easily download this comprehensive manual for free at manualshive.com. Explore detailed instructions, maintenance tips, and important safety information to fully maximize your TrailBlazer experience.

Share
Download
background image

DRIVE TRAIN 

 

Precautions

 

Before servicing any vehicle, please be sure to read all of the following precautions, which 
deal with personal safety, prevention of component damage and important points to take 
into consideration when servicing a motor vehicle: 

 

Always wear safety goggles or some type of eye/face protection when working 
with, around or under a vehicle.  

 

Be extremely careful while working on an operating engine, make sure you have no 
dangling jewelry, extremely loose clothes, power tool cords or other items that 
could get caught in any moving engine part.  

 

Never open, service or drain the radiator or cooling system when the engine is hot; 
serious burns can occur from the steam and hot coolant.  

 

Observe all applicable safety precautions when working around fuel. Whenever 
servicing the fuel system, always work in a well-ventilated area. Do not allow fuel 
spray or vapors to come in contact with a spark, open flame, or excessive heat (a 
hot drop light, for example). Keep a dry chemical fire extinguisher near the work 
area. Always keep fuel in a container specifically designed for fuel storage; also, 
always properly seal fuel containers to avoid the possibility of fire or explosion. 
Refer to the additional fuel system precautions later in this section.  

 

Fuel injection systems often remain pressurized, even after the engine has been 
turned OFF. The fuel system pressure must be relieved before disconnecting any 
fuel lines. Failure to do so may result in fire and/or personal injury.  

 

The EPA warns that prolonged contact with used engine oil may cause a number 
of skin disorders, including cancer! You should make every effort to minimize your 
exposure to used engine oil. Protective gloves should be worn when changing oil. 
Wash your hands and any other exposed skin areas as soon as possible after 
exposure to used engine oil. Soap and water, or waterless hand cleaner should be 
used.  

 

Never operate the engine without the proper amount and type of engine oil; doing 
so WILL result in severe engine damage.  

 

Brake fluid often contains polyglycol ethers and polyglycols. Avoid contact with the 
eyes and wash your hands thoroughly after handling brake fluid. If you do get 
brake fluid in your eyes, flush your eyes with clean, running water for 15 minutes. If 
eye irritation persists, or if you have taken brake fluid internally, IMMEDIATELY 
seek medical assistance.  

 

Timing belt maintenance is extremely important! Many models utilize an 
interference-type, non-freewheeling engine. If the timing belt breaks, the valves in 
the cylinder head may strike the pistons, causing potentially serious (also time-
consuming and expensive) engine damage. Refer to the maintenance interval 
charts in the front of this manual for the recommended replacement interval for the 
timing belt and to the timing belt section for belt replacement and inspection.  

 

Disconnecting the negative battery cable on some vehicles may interfere with the 
functions of the on-board computer system(s) and may require the computer to 
undergo a relearning process once the negative battery cable is reconnected.  

Summary of Contents for TrailBlazer






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TrailBlazer

AAMP of America iSimple Operation Manual preview
iSimple
Brand: AAMP of America Pages: 6
Back View RV-250 User Manual preview
RV-250
Brand: Back View Pages: 168
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Brand: Q'STRAINT Pages: 10
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Brand: Porsche Pages: 144
Toyota 2016 RAV4 Quick Reference Manual preview
2016 RAV4
Brand: Toyota Pages: 56
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Brand: Chevrolet Pages: 494
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
Ironton 44596 Owner'S Manual preview
44596
Brand: Ironton Pages: 7
Whispbar K561W Fitting Instructions Manual preview
K561W
Brand: Whispbar Pages: 15
Atera 022 681 Manual preview
022 681
Brand: Atera Pages: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Brand: RAM Pages: 7
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Brand: Cadillac Pages: 522
Oldsmobile 2004 Alero Quick Manual preview
2004 Alero
Brand: Oldsmobile Pages: 2
Road Ranger H392 Installation Manual preview
H392
Brand: Road Ranger Pages: 22
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112
BMW FXX ATM Emulator User And Installation Manual preview
FXX ATM Emulator
Brand: BMW Pages: 5
true-i HMBS-200 User Manual preview
HMBS-200
Brand: true-i Pages: 11
Honda Fit LX 2015 Manual preview
Fit LX 2015
Brand: Honda Pages: 4

Brands by name

Popular brands

Load more brands