manualshive.com logo in svg

Chevrolet TrailBlazer, Service Manual, Page: 188 / 677

Share
Download
Chevrolet TrailBlazer Service Manual Download Page 188

reflect the most wear. This is where the greatest force is exerted on the cylinder as the 
piston is forced down during combustion. This is known as thrust wear. Take the top, 90 
degree measurement and compare it to the bottom, 90 degree measurement. The 
difference between them is the cylinder taper. The amount of cylinder wall wear is always 
greater at the top of the cylinder than at the bottom. Any cylinder that has a taper of 0.0012 
in. (0.305 mm) or more must be re-bored. 

Compare the cylinder bore measurements to the size of the pistons to determine piston-to-
wall clearance. 

Crankshaft

 

Inspect the crankshaft for visible signs of wear or damage. All of the journals (piston and 
main bearing) should be perfectly round and smooth. Slight scores are normal for a used 
crankshaft, but should hardly be felt with a fingernail. Make the crankshaft measurements 
with a micrometer at the front and rear of each journal (x). Turn the micrometer 90 degrees 
and take two more readings (y), front and rear. The difference between the x and y reading 
is the out-of-round measurement. Generally, there should be no taper or out-of-roundness 
found. A difference up to 0.0005 in. (0.0127mm) for taper or out-of roundness is 
acceptable. All measurements should be within the factory specifications for journal 
diameters. 

If the crankshaft journals are within specifications, it is recommended that they be polished 
before being reusing the crankshaft. Polishing the crankshaft ensures that any minor burrs 
or scoring are smoothed, thereby reducing the chance of scoring the new crankshaft 
bearings. 

 

 

Pistons & Connecting Rods

 

Pressed-On Pistons 

 

The piston should be visually inspected for any signs of cracking or burning (caused by hot 
spots or detonation), scuffing or excessive wear on the skirts. The piston should move 
freely on the wrist pin, It should slide and pivot freely. Grasp the connecting rod securely, 
or mount it in a vise, and try to rock the piston back and forth along the centerline of the 
wrist pin. There should not be any excessive play evident between the piston and the wrist 
pin. If C-clips retain the pin in the piston then the piston may be equipped with wrist pin 
bushings in the connecting rod. There should not be any excessive play between the wrist 
pin and the rod bushing. Normal wrist pin clearance is approx. 0.001 - 0.002 in. (0.025-
0.051 mm). Check the manufacturer’s specifications for the exact values. 

 

Summary of Contents for TrailBlazer






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments