manualshive.com logo in svg

Chevrolet 2002 Astro, Owner'S Manual, Page: 245 / 400

Share
Download
Chevrolet 2002 Astro Owner'S Manual Download Page 245

5-18

Changing a Flat Tire

If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your hazard
warning flashers.

CAUTION:

Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over you or other
people. You and they could be badly injured.
Find a level place to change your tire. To help
prevent the vehicle from moving:

1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
4. Put the wheel blocks at the front and

rear of the tire farthest away from the
one being changed. That would be the
tire on the other side of the vehicle, at
the opposite end.

The following steps will tell you how to use the jack and
change a tire.

Summary of Contents for 2002 Astro

















































































































































































































































































































































































































Reviews:

No comments