manualshive.com logo in svg

Chevrolet 2002 Astro, Owner'S Manual, Page: 192 / 400

Share
Download
Chevrolet 2002 Astro Owner'S Manual Download Page 192

4-7

Avoid needless heavy braking. Some people drive in
spurts 

--

 heavy acceleration followed by heavy 

braking 

--

 rather than keeping pace with traffic. This 

is a mistake. Your brakes may not have time to cool
between hard stops. Your brakes will wear out much
faster if you do a lot of heavy braking. If you keep pace
with the traffic and allow realistic following distances,
you will eliminate a lot of unnecessary braking. That
means better braking and longer brake life.

If your engine ever stops while you’re driving, brake
normally but don’t pump your brakes. If you do, the
pedal may get harder to push down. If your engine
stops, you will still have some power brake assist. But
you will use it when you brake. Once the power assist is
used up, it may take longer to stop and the brake pedal
will be harder to push.

Anti-Lock Brake System (ABS)

Your vehicle has anti

-

lock brakes. ABS is an advanced

electronic braking system that will help prevent a
braking skid.

When you start your engine and begin to drive away,
your anti

-

lock brake system will check itself. You may

hear a momentary motor or clicking noise while this test
is going on. This is normal.

United States

Canada

If there’s a problem with the anti

-

lock brake system, 

this warning light will stay on. See “Anti

-

Lock Brake

System Warning Light” in the Index.

Summary of Contents for 2002 Astro

















































































































































































































































































































































































































Reviews:

No comments