Chevrolet 2002 Astro Owner'S Manual Download Page 149

Page: 149 / 400

2-76

Here are things some owners ask about. None of these
indicate a problem with your fuel gage:
D At the gas station, the gas pump shuts off before the

gage reads full.

D The fuel tank will take either a little more or a little

less fuel to fill up than the gage shows.

D The gage moves a little when you turn a corner or

speed up.

D The gage doesn’t go back to empty when you turn

off the ignition.

Low Fuel Light

The LOW FUEL light will
come on briefly when you
are starting the engine.

This light comes on when the fuel tank is low on fuel.
To turn it off, add fuel to the fuel tank. See “Fuel” in
the Index.

Summary of Contents for 2002 Astro
















































































































































































































































































































































































































Search results

Summary of Contents for 2002 Astro

Reviews:

Chevrolet 2002 Astro, Owner'S Manual, Page: 149 / 400

Search results

Summary of Contents for 2002 Astro

Reviews: