Chevrolet 2002 Astro Owner'S Manual Download Page 122

Page: 122 / 400

2-49

Reading Lamps

Press the button near each
lamp to turn the reading
lamps on and off.

The lamps can also be swiveled to point in the direction
you want.

Installing a Garage Door Opener

If you have a garage door opener, the front
overhead compartment can be used to conveniently
store the opener.

1. To install the garage door opener, first open the

compartment door by pressing the latch forward.

2. Peel the protective

backing from the
hook and loop patch.

3. Press it firmly to the back of your garage

door opener, as close to the center of the opener
as possible.

4. Center the garage door opener activation button over

the console door button and press the opener firmly
into place.

Summary of Contents for 2002 Astro
















































































































































































































































































































































































































Search results

Summary of Contents for 2002 Astro

Reviews:

Chevrolet 2002 Astro, Owner'S Manual, Page: 122 / 400

Search results

Summary of Contents for 2002 Astro

Reviews: