Home
/
Chevrolet
/
2002 Astro
/
Owner'S Manual

Chevrolet 2002 Astro, Owner'S Manual, Page: 146 / 400

Share

Page: 146 / 400

Chevrolet 2002 Astro Owner'S Manual Download Page 146

2-73

CAUTION:

Don’t keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches fire. You or others could be burned.
Check your oil as soon as possible and have your
vehicle serviced.

NOTICE:

Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.

Security Light

This light will come on
briefly when you turn the
key to START.

The light will stay on until the engine starts. If the light
flashes, the Passlock

R

System has entered a tamper

mode. If the vehicle fails to start, see “Passlock” in
the Index.

If the light comes on continuously while driving and
stays on, there may be a problem with the Passlock
System. Your vehicle will not be protected by Passlock,
and you should see your GM dealer.

«
...
144
145
146
147
148
...
»

Summary of Contents for 2002 Astro

















































































































































































































































































































































































































Reviews:

No comments