manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 93

93 

 

E840-
0001 

Fixing Shutter Motor error 
The Fixing Shutter HP 
Sensor (PS53) failed the 
detection at the Fixing 
Shutter operation. 

1. Check the operation of the Fixing Shutter Gear 
(overload, etc.). 2. Check the operation of the 
Fixing Shutter Motor (M15) at the initialization 
operation of the Fixing Shutter. 3. Check the 
detection of the Fixing Shutter HP Sensor (PS53) 
(if the Sensor operates normally). 4. Check the 
drawer of the Fixing Assembly and the host 
machine. 5. Replace the Fixing Upper Unit and the 
Fixing Drawer Harness Unit. 6. Replace the Main 
Driver PCB (PCB2) (check the fuse (FU11)). 

E880-
0001 

Controller Fan error 
Error in the Main Controller 
Cooling Fan (FM4) is 
detected. 

Connector disconnection, failure of Fan. 

E880-
0005 

Controller Fan error 
Connector disconnection, 
failure of Fan. 

Error in the HDD Cooling Fan (FM) is detected. 

E905-
0001 

POD Deck Air Assist Fan 
error 
[POD Deck Lite] When the 
Air Assist Swing Motor fails 
to return to the HP although 
a specified period of time 
has passed 

1. Check connector disconnection/improper 
connection. => Disconnect and then connect the 
connector. Target connector: Deck Lite Controller 
J04, J05 BoxDriver J51, J52, J57 2. Replace the 
Swing Motor (M3) and the Air Assist Fan (FM1, 
FM2, FM3). 3. Replace the Deck Lite Controller 
PCB. 4. Replace the BoxDriver PCB. 

 

Code 

Description 

Remedy 

E905-
0002 

POD Deck Air Assist Fan 
error 
[POD Deck Lite] When the 
Pickup Motor Cooling Fan is 
not locked 

1. Check connector disconnection/improper 
connection. => Disconnect and then connect the 
connector. Target connector: Deck Lite Controller 
J30 2. Replace the Motor Cooling Fan (FM4). 3. 
Replace the Deck Lite Controller PCB. 

E905-
0003 

POD Deck Air Assist Fan 
error 
[POD Deck Lite] When the 
Pickup Motor Cooling Fan is 
not unlocked 

1. Check connector disconnection/improper 
connection. => Disconnect and then connect the 
connector. Target connector: Deck Lite Controller 
J30 2. Replace the Motor Cooling Fan (FM4). 3. 
Replace the Deck Lite Controller PCB. 

E906-
0001 

POD Deck Air Heater error[ 
POD Deck Lite] Air Heater 
high temperature error 
When 120 deg C or higher 
temperature is detected for 
1 second consecutively 

1. Check connector disconnection/improper 
connection. - > Disconnect and then connect the 
connector. Target connector: Deck Lite Controller 
J03, J05 BoxDriver J52, J54, J58, J59 2. Replace 
the Air Heater. 3. Replace the Deck Lite Controller 
PCB 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands