manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 56

56 

 

Driver side (12V to 1pin, 5V to 3pin, 3.3V to 
4pin). -> If not, replace the DC-DC Converter 
PCB. 4. Replace the Duplex Driver PCB 
(PCB4). 5. Replace the DC Controller PCB 
(PCB1). 

E197-
0004 

Error in Relay PCB connection 
detection 
Connection between the DC 
Controller PCB (PCB1) and the 
Relay PCB (PCB5) is 
disconnected. 

1. Check the connection of the DC Controller 
PCB (PCB1) and the Relay PCB (PCB5). DC 
Controller side: J451, Relay side: J514 2. 
Replace the Relay PCB (PCB5). 3. Replace 
the DC Controller PCB (PCB1). 

E197-
0005 

Error in Main Driver PCB Analog 
Connector connection detection 
Connection between the DC 
Controller PCB (PCB1) and the 
Main Driver PCB (PCB2) is 
disconnected. 

1. Check the connection of the DC Controller 
PCB (PCB1) and the Main Driver PCB 
(PCB2). DC Controller side: J413, Main Driver 
side: J124 2. Replace the Main Driver PCB 
(PCB2). 3. Replace the DC Controller PCB 
(PCB1). 

E197-
0006 

Error in Feed Driver PCB 
Drawer Connector connection 
detection 
Connection between the DC 
Controller PCB (PCB1) and the 
Feed Driver PCB (PCB3) is 
disconnected. 

1. Check the connection between the DC 
Controller PCB (PCB1) and the Fixing Feed 
Drawer. DC Controller side: J431, J432, Fixing 
Feed Drawer (host machine side): J3002D 
Fixing Feed Drawer (Fixing Feed side): 
J3002L, Feed Driver side: J300, J301 2. 
Replace the Feed Driver PCB (PCB3). 3. 
Replace the DC Controller PCB (PCB1). 

E197-
0008 

Error in Fixing Drawer 
Connector connection detection 
Connection between the DC 
Controller PCB (PCB1) and the 
Main Driver PCB (PCB2) is 
disconnected. 

1. Check the connection between the Main 
Driver PCB (PCB2) and the Fixing Drawer. 
Main Driver side: J105, Fixing Drawer (host 
machine side): J3001D Check the Harness of 
the Fixing Drawer (Fixing side) (J3001L). 2. 
Replace the Main Driver PCB (PCB2). 

E197-
0009 

Error in the Process Unit 
connection detection 
Connection between the Main 
Driver PCB (PCB2) and the 
Process Unit is disconnected. 

1. Check the connection between the Main 
Driver PCB (PCB2) and the Process Unit. PCB 
side: J107, Process Unit side: J3060 2. 
Replace the Process Unit. 

E197-
0010 

Error in Primary Charging High 
Voltage PCB connection 
detection 
Connection between the Main 
Driver PCB (PCB2) and the 
Primary Charging High Voltage 
PCB (PCB11) is disconnected. 

1. Check the connection between the Main 
Driver PCB (PCB2) and the Primary Charging 
High Voltage PCB (PCB11). Main Driver side: 
J111, Primary Charging High Voltage side: 
J3501 2. Replace the Primary Charging High 
Voltage PCB (PCB11). 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands