manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 51

51 

 

the way 1-C-1. Check abrasion of the Slider 
Pin. Replace the Slider Pin. 1-C-2. Replace 
the Pre-transfer Charging Assembly. 2. 
Replace the DC Controller PCB (PCB1). 

E067-
0001 

Developing high voltage output 
leak error 
The leak detection signal was 
detected 5 times in a row for every 
20 msec. 

1. Check the connection between the Main 
Driver PCB (PCB2) and the High Voltage 
Unit. Main Driver side: J112, High Voltage 
Unit side: J3098 2. Check the connection 
between the Relay PCB (PCB5) and the 
High Voltage Unit. Relay side: J519, High 
Voltage Unit side: J3099 3. Replace the 
Developing Assembly. 4. Check the 
connection point of the Developing 
Assembly. If it is soiled, clean it. 5. Check 
the connection inside of the High Voltage 
Unit. Check the connection of the High 
Voltage Unit Relay (J3097) and the 
Developing High Voltage PCB (J3511). High 
Voltage Unit Relay (J3099) and Pre-transfer 
Charging PCB (J3545, J3500, J3510) 6. 
Replace the Main Driver PCB (PCB2). 

E068-
0001 

Pre-transfer charging high voltage 
output leak error 
The leak detection signal was 
detected 5 times in a row for every 
20 msec. 

1. Check the connection between the Main 
Driver PCB (PCB2) and the High Voltage 
Unit. Main Driver side: J112, High Voltage 
Unit side: J3098 2. Check the connection 
between the Relay PCB (PCB5) and the 
High Voltage Unit. Relay side: J519, High 
Voltage Unit side: J3099 3. Replace the Pre-
transfer Charging Assembly. 4. Check the 
connection inside of the High Voltage Unit. 
Check the connection of the High Voltage 
Unit Relay (J3098) and the Transfer High 
Voltage PCB (J3544). Check the connection 
of the High Voltage Unit Relay (J3099) and 
the Pre-transfer Charging PCB (J3545, 
J3500) 5. Replace the Main Driver PCB 
(PCB2). 6. Replace the Pre-transfer High 
Voltage Connector (FM4- 1007). 7. Replace 
the Pre-transfer Transformer (Post Charging 
Trance) of the High Voltage Unit. 

E069-
0001 

Transfer high voltage output leak 
error 
The leak detection signal was 
detected 5 times in a row for every 
20 msec 

1. Check the connection between the Duplex 
Driver PCB (PCB4) and the High Voltage 
Unit. Check the connection at Duplex Driver 
side (J343) and the Transfer High Voltage 
side (J3066). Check the connection at 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands