manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 43

43 

 

Motor side: J2107, J3044 (relay), PCB side: J330 
(Duplex Driver PCB (PCB4)) 3. Replace the ETB 
Disengage Sensor (PS56). 4. Replace the Duplex 
Feed Left Motor (M19). 5. Replace the Duplex 
Driver PCB (PCB4). 6. Replace the DC Controller 
PCB (PCB1). NOTE: Check if the Disengagement 
Cam is stained. If necessary, clean it. Check if the 
drive system (gear, Motor, one-way) is failed. If 
necessary, replace it. Check if the link with the 
Fixing Feed Handle is failed. If necessary, replace 
it. 

E020-
0000 

Developing Assembly toner 
absent error 
Toner in the Developing 
Assembly was empty for 2 
minutes. 

1. Check the connection of the Developing Toner 
Sensor (TS1). Sensor side: J2133, J3089 (relay), 
PCB side: J3088 (relay), J114 (Main Driver PCB 
(PCB2)) 2. Check the connection of the Magnet 
Roller Clutch (CL5). Sensor side: J2036, J3124 
(relay), J3090 (relay) PCB side: J3091(relay), 
J115 (Main Driver PCB (PCB2)) 3. Check the 
connection of the Toner Feed Motor (M28). Motor 
side: J2035, J3124 (relay), J3090 (relay) PCB 
side: J3091(relay), J115 (Main Driver PCB 
(PCB2)) 4. Check the connection of the Buffer 
Toner Sensor (TS3). Sensor side: J2039, J3124 
(relay), J3090 (relay) PCB side: J3091(relay), 
J115 (Main Driver PCB (PCB2)) 5. Replace the 
Developing Toner Sensor (TS1). 6. Replace the 
Magnet Roller Clutch (CL5). 7. Replace the Toner 
Feed Motor (M28). 8. Replace the Buffer Toner 
Sensor (TS3). 9. Replace the Main Driver PCB 
(PCB2). 10. Replace the DC Controller PCB 
(PCB1). 

E020-
0001 

Error in Developing Toner 
Sensor connection detection 
The connection detection 
port was OFF at power-on. 

1. Check the connection of the Developing Toner 
Sensor (TS1). Sensor side: J2133, J3089 (relay), 
PCB side: J3088 (relay), J114 (Main Driver PCB 
(PCB2)) 2. Replace the Developing Toner Sensor 
(TS1). 3. Replace the Main Driver PCB (PCB2). 4. 
Replace the DC Controller PCB (PCB1). 

E020-
0002 

Error in Buffer Toner Sensor 
connection detection 
The connection detection 
port was OFF at power-on. 

1. Check the connection of the Buffer Toner 
Sensor (TS3). Sensor side: J2039, J3124 (relay), 
J3090 (relay) PCB side: J3091 (relay), J115 (Main 
Driver PCB (PCB2)) 2. Replace the Buffer Toner 
Sensor (TS3). 3. Replace the Main Driver PCB 
(PCB2). 4. Replace the DC Controller PCB 
(PCB1). 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands