manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 91

91 

 

Image Exhaust Fan (FM3) is turned 
ON. 

E808-
0001 

Fixing Power Supply error 
Detected 145V (100V/120V 
model)/290V (230V model) or higher 
inlet voltage at power-on. 

1. Check the outlet voltage. -> Connect 
to the correct outlet. 2. Check the 
connection between the Main Driver 
PCB (PCB2) and the Fixing Power 
Supply PCB (PCB10). 3. Replace the 
Fixing Power Supply PCB (PCB10). 4. 
Replace the Main Driver PCB (PCB2). 

E808-
0002 

Fixing Power Supply error 
Detected 75 V (100V/120V model)/150 
V (230V model) or higher inlet voltage 
at power-on. 

1. Check the outlet voltage. -> Connect 
to the correct outlet. 2. Check the 
connection between the Main Driver 
PCB (PCB2) and the Fixing Power 
Supply PCB (PCB10). 3. Replace the 
Fixing Power Supply PCB (PCB10). 4. 
Replace the Main Driver PCB (PCB2). 

 

Code 

Description 

Remedy 

E808-
0003 

Fixing Power Supply error 
Inlet current is 1A or lower 
for 1 second or longer 
although the maximum 
voltage is output. 

1. Check the clogging of the Fixing Power Supply 
Cooling Fan (FM7). 2. Check the clogging of the 
Louver on right side of the host machine (Multi-
purpose Tray side). 3. Check the connection of the 
Fixing Power Supply PCB (PCB10) Output 
Connector. 4. Replace the Fixing Power Supply 
PCB (PCB10). 

E808-
0004 

Fixing Power Supply error 
Detected OFF with 12V of 
the Main Driver PCB (PCB2) 
output. 

Replace the Main Driver PCB (PCB2). 

E808-
0005 

12V OFF detection when 
relay is turned ON 
Detected OFF with 12V of 
the Fixing Power Supply 
output after IH relay is 
turned ON. 

1. Check the conduction of the Fixing Thermal 
Switch 1/2 (TP1/2). 2. Check the drawer between 
the Fixing Assembly and the host machine. 3. 
Check the connection between the Main Driver 
PCB (PCB2) and the Fixing Power Supply PCB 
(PCB10). 4. Replace the Fixing Power Supply 
Unit. 5. Replace the Main Driver PCB (PCB2). 

E808-
0006 

ASIC error 

Replace the DC Controller PCB (PCB1). 

E808-
0007 

Fixing Power Supply error 
Inlet voltage and the IH 
Power Supply ID are not 

Check the connection between the Main Driver 
PCB (PCB2) and the Fixing Power Supply PCB 
(PCB10). Replace the Fixing Power Supply PCB 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands