manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 12

12 

 

PCB and the DADF. 

E413-
0001 

Release Motor (M2) error 
The sensing level of the release 
motor HP sensor (SR11) does not 
change within a specified period 
when the release motor (M2) is 
driven. 

1. Replace the Release Motor HP Sensor 
(SR11). 2. Replace the Release Motor 
(M2). 3. Replace the ADF Driver PCB. 

E413-
0002 

Release Motor (M2) error 
The sensing level of the release 
motor HP sensor (SR11) does not 
change within a specified period 
when the release motor (M2) is 
driven. 

1. Replace the Release Motor HP Sensor 
(SR11). 2. Replace the Release Motor 
(M2). 3. Replace the ADF Driver PCB. 

E490-
0001 

Different DADF model error 
Not proper DADF is installed. 

1. Installed DADF is a different model. 2. 
Replace the Reader Controller PCB (UN4). 
3. Replace the DC Controller PCB (UN2). 
4. Replace the Main Controller PCB 2 
(UN14). 

E500-
0000 

Communication error 
(Staple/Booklet Finisher) 
The communication with the host 
machine is interrupted. 

1. Check the cable. 2. Replace the Finisher 
Controller PCB. 3. Replace the DC 
Controller PCB. 

E500-
0001 

Communication error (Inner 
Finisher) 
The communication with the host 
machine is interrupted. 

1. Check the cable. 2. Replace the Finisher 
Controller PCB. 3. Replace the DC 
Controller PCB. 

E503-
0002 

Communication error 
Communication between the 
Saddle Controller and the Finisher 
Controller is suspended. 

1. The wiring between the finisher controller 
PCB and saddle controller PCB is faulty. 2. 
The finisher controller PCB is faulty. 3. The 
saddle stitcher controller PCB is faulty. 

E503-
0003 

Communication error 
Communication between the 
Punch Controller and the Finisher 
Controller is suspended. 

1. The wiring between the finisher controller 
PCB and punch Controller PCB is faulty. 2. 
The punch controller PCB is faulty. 3. The 
finisher controller PCB is faulty. 4. The host 
machine DC Controller PCB is faulty. 

E505-
0001 

EEPROM error 
The checksum data for the 
EEPROM on the finisher controller 
PCB has an error. 

Replace the Finisher Controller PCB. 

 

Code 

Description 

Remedy 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands