manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 49

49 

 

open circuit, the caught cable). 6. 
Replace the parts. • Primary Charging 
Assembly • Primary Charging High 
Voltage PCB • Drum Motor (M1) • Main 
Driver PCB (PCB2) • DC Controller PCB 
(PCB1) 

E064-
00FF 

High voltage setting error 
With the state in which the developing 
AC is output, 600V or higher 
developing DC output was detected. 
(Basically, this error is not detected. 
However, to detect that the image 
formation-related backup data is 
corrupted or to protect the hardware in 
case of 600V or higher developing DC 
output, this is to be an error.) 

1. Turn OFF and then ON the main 
power. 2. Replace the DCON PCB. 

E065-
0001 

Primary charging/grid high voltage 
output leak error 
The leak detection signal was detected 
5 times in a row for every 20 msec. 

1. Check the connection between the 
Main Driver PCB (PCB2) and the High 
Voltage Unit. Main Driver side: J111, 
High Voltage Unit side: J3097 2. Check 
the connection between the Relay PCB 
(PCB5) and the High Voltage Unit. 
Relay side: J519, High Voltage Unit 
side: J3099 3. Replace the Primary 
Charging Assembly. 4. Check the 
connection inside of the High Voltage 
Unit. High Voltage Unit Relay (J3097) 
and Primary Charging High Voltage 
PCB (PCB11) (J3501) High Voltage 
Unit relay (J3099) and Pre-transfer 
Charging PCB (PCB26) (J3545, J3500) 
5. Replace the Main Driver PCB 
(PCB2). 6. Replace the Primary Grid 
High Voltage Connector (FM4- 1006). 

 

Code 

Description 

Remedy 

E066-
0001 

Pre-transfer Charging Shutter HP 
open error 
The Pre-transfer Charging Shutter 
Sensor (PS95) detects that the 
shutter is opened although it is 
moved to the close position. 

1. Check the position of the Pre-transfer 
Charging Shutter. 1-A. In the case that the 
Pre-transfer Charging Shutter fails to 
operate (stopped at HP at front side) Check 
the connection of the Pre-transfer Charging 
Wire Cleaning Motor (M7). Sensor side: 
J3108, J3089 (relay), PCB side: J3088 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands