manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 17

17 

 

OFF when the tray 1 shift motor is at a 
stop. 

finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E542-
0001 

Additional Tray Lift Motor timeout error 
Unable to complete the operation even 
after the specified period of time during 
initial rotation. When the Motor remains in 
the same area for the specified period of 
time and the same symptom occurs again 
after the first retry, it is detected as an 
error. 

1. Check if the Motor (M12) 
Connector is physically removed. 2. 
Check if the Motor failure occurs. 3. 
Check if the Additional Tray Clock 
Sensor (S23) Connector is 
physically removed. 4. Check if the 
Additional Tray Clock Sensor (S23) 
failure occurs. 

E542-
0002 

Additional Tray Lift Motor clock error 
At initial rotation, when the Tray Lift Motor 
rotates and clock signal is not detected 
within the specified period of time, it is 
detected as an error if the same symptom 
occurs again after the first retry. 

1. Check if the Motor (M12) 
Connector is physically removed. 2. 
Check if the Motor failure occurs. 3. 
Check if the Additional Tray Clock 
Sensor (S23) Connector is 
physically removed. 4. Check if the 
Additional Tray Clock Sensor (S23) 
failure occurs. 

E542-
8001 

Tray 1 time out error 
If the tray does not return to home position 
when the tray 1 shift motor is driven for 25 
seconds. If the tray does not move to 
other area when tray 2 shift motor is 
driven for 5 seconds. 

1. The Tray 2 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 2 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 shift motor (M105) is faulty. 5. 
The finisher controller PCB is faulty. 

E542-
8002 

Tray 2 shift area error 
The upper limit area is reached before the 
tray 2 paper surface sensor 1 detects the 
paper surface during paper surface 
detection operation. A discontinuous area 
is detected during tray operation. During 
evacuation operation, arrival at the area 
beyond the tray 2 paper surface sensor 2 
is detected before this sensor detects 
paper surface. 

1. The tray 2 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 2 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 2 shift motor (M105) is faulty. 5. 
The finisher controller PCB is faulty. 

E542-
8004 

The tray 2 shift motor clock error 
The FG input cannot be detected when 
the tray 2 shift motor has been driven for 
0.2 second. 

1. The Tray 2 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 2 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 shift motor (M105) is faulty. 5. 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands