manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 25

25 

 

Position Sensor does not change 
although the Paper Fold Motor is 
driven for a specified period of 
time. 

roller drive mechanism is faulty. 3. The 
paper folding motor (M2) is faulty. 4. The 
saddle stitcher controller PCB is faulty. 

E5F2-
8001 

Guide home position error 
The guide home position sensor 
does not turn ON when the guide 
motor has been driven for 700 
pulses. 

1. The guide home position sensor (PI13) 
is faulty. 2. The guide plate drive 
mechanism is faulty. 3. The guide Motor 
(M3) is faulty. 4. The saddle stitcher 
controller PCB is faulty. 

E5F2-
8002 

Guide home position error 
The guide home position sensor 
does not turn OFF when the 
guide motor has been driven for 
50 pulses. 

1. The guide home position sensor (PI13) 
is faulty. 2. The guide plate drive 
mechanism is faulty. 3. The guide Motor 
(M3) is faulty. 4. The saddle stitcher 
controller PCB is faulty. 

E5F3-
8001 

Aligning plate home position 
error 
The aligning plate home position 
sensor does not turn ON when 
the aligning plate motor has 
been driven for 500 pulses. 

1. The aligning plate home position sensor 
(PI5) is faulty. 2. The aligning plate drive 
mechanism is faulty. 3. The aligning motor 
(M5) is faulty. 4. The saddle stitcher 
controller PCB is faulty. 

E5F3-
8002 

Aligning plate home position 
error 
The aligning plate home position 
sensor does not turn OFF when 
the aligning plate motor has 
been driven for 50 pulses. 

1. The aligning plate home position sensor 
(PI5) is faulty. 2. The aligning plate drive 
mechanism is faulty. 3. The aligning motor 
(M5) is faulty. 4. The saddle stitcher 
controller PCB is faulty. 

E5F4-
8001 

Stitcher (rear) home position 
error 
The stitching home position 
sensor does not turn ON when 
the stitch motor (rear) has been 
driven backward for 0.5 sec. 

1. The stitcher home position sensor (rear) 
(SW5) is faulty. 2. The stitcher (rear) is 
faulty. 3. The saddle stitcher controller 
PCB is faulty 

E5F4-
8002 

Stitcher (rear) home position 
error 
The stitching home position 
sensor does not turn OFF when 
the stitch motor (rear) has been 
driven forward for 0.5 sec. 

1. The stitcher home position sensor (rear) 
(SW5) is faulty. 2. The stitcher (rear) is 
faulty. 3. The saddle stitcher controller 
PCB is faulty. 

E5F5-
8001 

Stitcher (front) home position 
error 
The stitching home position 
sensor does not turn ON when 
the stitch motor (front) has been 

1. The stitcher home position sensor (front) 
(SW7) is faulty. 2. The stitcher (front) is 
faulty. 3. The saddle stitcher controller 
PCB is faulty. 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands