manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 37

37 

 

0003 

Cooling Fan (FM7) 
When lock signal failed to be 
detected for 15 sec while the Paper 
Cooling Fan (FM7) is driven. * The 
same condition is detected after the 
error retry is performed. 

(J2209/J2509/J206). 2. Replace the Paper 
Cooling Fan (FM7). 3. Replace the DC 
Controller PCB (UN2). 

E840-
0000 

Edge Shutter Home Position error 
When the home position of the 
shutter is not detected 

1. Check connection of the Connectors 
(J2039/J2037/J2507/ J215). 2. Replace the 
fixing film edge shutter HP sensor (S10). 3. 
Replace the fixing film edge shutter motor 
(M8). 4. Replace the DC controller PCB 
(UN2). 

 

Code 

Description 

Remedy 

E840-
0001 

Failure of Fixing Film Edge Cooling 
Fan (Rear) (FM1) 
When the lock signal is detected for 15 
sec while the fixing film edge cooling 
fan (rear) stops. * The same status is 
detected again after the retry 
operation. 

1. Check connection of the Connectors 
(J2036/J215). 2. Replace the fixing film 
edge cooling fan (rear) (FM1) 3. 
Replace the DC controller PCB (UN2). 

E840-
0002 

Rotation error of Fixing Film Edge 
Cooling Fan (Rear) (FM1) 
When the lock signal is detected for 15 
sec while the fixing film cooling fan 
(rear) operates. * The same status is 
detected again after the retry 
operation. 

1. Check connection of the Connectors 
(J2036/J215). 2. Replace the fixing film 
edge cooling fan (rear) (FM1) 3. 
Replace the DC controller PCB (UN2). 

E840-
0003 

Failure of Fixing Film Edge Cooling 
Fan (Front) (FM2) 
When the lock signal is detected for 15 
sec while the fixing film edge cooling 
fan (front) stops. * The same status is 
detected again after the retry 
operation. 

1. Check connection of the Connectors 
(J2035/J215). 2. Replace the fixing film 
edge Cooling fan (front) (FM2) 3. 
Replace the DC controller PCB (UN2). 

E840-
0004 

Rotation error of Fixing Film Edge 
Cooling Fan (Front) (FM2) 
When the lock signal is detected for 15 
sec while the fixing film edge cooling 
fan (front) operates. * The same status 
is detected again after the retry 
operation. 

1. Check connection of the Connectors 
(J2035/J215). 2. Replace the fixing film 
edge cooling fan (front) (FM2). 3. 
Replace the DC controller PCB (UN2). 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands