manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 55

55 

 

E121-
0001 

Laser Scanner Cooling Fan 
error. 
The Fan stop signal is detected 
for 5 seconds or longer and retry 
is failed 4 times in a row 
although the Laser Scanner 
Cooling Fan (FM16) is turned 
ON. 

1. Check the connection of the Connector. 2. 
Replace the Laser Scanner Cooling Fan 
(FM16). 

E197-
0001 

Error in Main Driver PCB 
connection detection 
Failed to establish a 
communication between the DC 
Controller PCB (PCB1) and the 
Main Driver PCB (PCB2). 

1. Check the connection of the DC Controller 
PCB (PCB1) and the Main Driver PCB 
(PCB2). DC Controller side: J411, J412, Main 
Driver side: J125, J126 2. Check the Main 
Driver PCB (PCB2) power supply connection. 
Check the connection at the Main Driver side 
(J128) and the DC Controller side (J414), and 
check the voltage. 3. Replace the Main Driver 
PCB (PCB2). 4. Replace the DC Controller 
PCB (PCB1). 

E197-
0002 

Error in Feed Driver PCB 
connection detection 
Failed to establish a 
communication between the DC 
Controller PCB (PCB1) and the 
Feed Driver Pub (PCB3). 

1. Check the connection of the DC Controller 
PCB (PCB1) and the Feed Driver PCB 
(PCB3). DC Controller side: J421, Feed Driver 
side: J204 2. Check the connection of the 
Feed Driver PCB (PCB3) and the DC-DC 
Converter PCB. Check the connection at the 
Feed Driver side (J218) and the DC-DC 
Converter side (J9033). 3. Check the power 
supply of the Feed Driver PCB (PCB3). Check 
if appropriate voltages are applied to the Feed 
Driver side (12V to 1pin, 5V to 3pin, 3.3V to 
4pin). -> If not, replace the DC-DC Converter 
PCB. 4. Replace the Feed Driver PCB (PCB3). 
5. Replace the DC Controller PCB (PCB1). 

E197-
0003 

Error in Duplex Driver PCB 
connection detection 
Failed to establish a 
communication between the DC 
Controller PCB (PCB1) and the 
Duplex Driver PCB (PCB4). 

1. Check the connection between the DC 
Controller PCB (PCB1) and the Fixing Feed 
Drawer. DC Controller side: J431, J432, Fixing 
Feed Drawer (host machine side): J3002D 
Fixing Feed Drawer (Fixing Feed side): 
J3002L, Duplex Driver side: J300, J301 2. 
Check the connection of the Duplex Driver 
PCB (PCB4) and the DC-DC Converter PCB. 
Check the connection at the Duplex Driver 
side (J311) and the DC-DC Converter side 
(J9034). 3. Check the power supply of the 
Duplex Driver PCB (PCB4). Check if 
appropriate voltages are applied to the Duplex 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands